Pipe Repair in Comer, GA — Located Precisely, Fixed Permanently
In Comer's mixed housing stock, a single repair call might involve copper sweated joints, threaded galvanized fittings, push-connect PEX transitions, or CPVC drain arms — sometimes all in the same house. Our techs carry the materials and know the techniques for every pipe type commonly found in GA homes.
Acoustic & Thermal Leak LocationAll Pipe MaterialsPress-Fit & Sweat CapableLicensed in GA
Our Capabilities
How Masters Plumbing Service Approaches Pipe Repair in Comer
Our techs work on every pipe material found in Comer, GA homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
We use thermal imaging as a complement to acoustic detection — particularly useful for slab leaks and leaks inside insulated wall cavities where sound transmission is reduced.
🛠️
All Pipe Materials & Joining Methods
Our techs are proficient in copper sweating (soldering), press-fit connections (ProPress system), CPVC solvent welding, PEX crimp and expansion fitting installation, threaded galvanized repair, and ABS/PVC drain line work. We match the repair method and material to the existing pipe system rather than forcing incompatible transitions.
🔒
Pressure-Tested Before We Leave
Drain line repairs are water-tested by running fixtures through the repaired section and visually confirming no seepage at the repair joint and downstream.
Our Pipe Repair Services
What We Fix — Pipe by Pipe, Material by Material
Pipe failures have different causes depending on material type, age, water chemistry, and installation history. Here's how we address each category.
Copper
Copper Pipe Repair & Repipe
Copper failures most often involve pinhole corrosion in soft copper tubing from aggressive water chemistry, failed soldered joints, or fatigue cracks at fittings in high-vibration locations. We locate the failure precisely, cut out the failed section, and install either a sweated repair coupling or a press-fit connector — both rated to ASTM B88 standards for potable water service.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
PEX is also the material of choice for extending or reconfiguring supply runs during remodel work. Its flexibility reduces fitting count and eliminates the need for torch work inside walls.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
A burst pipe from freezing or sudden pressure surge requires immediate water shutoff and precise repair. We locate the failure, determine whether it's a single failure point or multiple freeze-damaged sections, and repair with a method appropriate to the pipe material — press-fit coupling for copper, expansion coupling for PEX-A, or a mechanical repair coupling for emergency situations.
Slab Leaks
Under-Slab Pipe Leak Repair
Supply line leaks under a concrete slab are identified by acoustic detection and confirmed by thermal imaging. Once located, we evaluate three repair options: direct-access repair (jackhammering to the pipe, repairing the section, and patching the slab); rerouting the line through the wall framing above slab to bypass the failed underground run; or epoxy pipe lining for older copper systems with systemic pinhole corrosion.
Full Repipe
Whole-House Repipe Service
A full repipe in Comer typically completes in 2–3 days for a standard single-family home. You're without water for a portion of each day; we plan the schedule to minimize disruption to occupied rooms.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe — We Shut the Water If Needed
For emergency burst pipe calls, we dispatch immediately. For suspected slow leaks, we schedule at the earliest available slot and confirm before arrival.
2
Pressure Test & Acoustic / Thermal Detection
We pressurize the supply system and monitor for pressure drop to confirm an active leak. Then acoustic listening devices and the thermal camera locate the failure to within a small area — telling us which section of wall, floor, or slab to open.
3
Flat-Rate Quote & Minimal Access Opening
You receive a flat-rate quote covering the specific repair based on what the detection confirmed. We open only what needs to be opened — typically a 12–18 inch drywall or flooring access, not a full wall section.
4
Repair & Pressure Test — Then You're Done
You receive a written summary of what failed, what we installed, and the warranty terms before we leave.
Customer Reviews
Masters Plumbing Service Pipe Repair — How We Handle It
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Comer
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Comer, GA
★★★★★
Pipe burst in a rental property at 2 AM — Masters Plumbing Service's emergency line answered immediately, talked my tenant through the main shutoff, and had a tech there in 45 minutes. Freeze crack in a PEX line in an exterior wall. Repair and insulation wrap done in under two hours. Detailed receipt for insurance documentation. Exactly what I needed as a landlord dealing with a crisis remotely.
— F. Okoro, Comer, GA
Common Questions
Pipe Repair Questions We Answer Every Day
Watch your water meter with all fixtures off. If the meter dial is moving or the leak indicator light is turning, water is escaping somewhere in your supply system. Other signs: unexplained increases in your monthly water bill, soft or discolored spots on walls or ceilings, mold or mildew smell in a room without a visible source, or a running sound inside walls when all fixtures are off.
In some cases — particularly for older copper systems with multiple pinhole failures along a supply run — rerouting the line through accessible framing rather than repairing it in place is more practical and more permanent. We present both options when they're both viable.
A slab leak is a supply line or drain line failure in a pipe that runs through or under the concrete foundation slab. Supply line slab leaks are the more urgent scenario — pressurized water escaping under the slab saturates the subgrade, can undermine the foundation, and drives significant water bills.
We assess galvanized condition when we're on-site — visible exterior corrosion, interior scale visible at the cut failure point, and water pressure readings all tell us how advanced the system deterioration is. We give you the repair-vs-repipe math honestly so you can make the decision that fits your timeline and budget.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
For slab access openings, we clean up concrete debris, complete the pipe repair, and patch the concrete. Tile or flooring restoration over a slab patch is normally a separate trade.
Service Area
Masters Plumbing Service Pipe Techs Serving Comer, GA
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Comer homes and businesses.
Precision Pipe Repair in Comer, GA — We Find It Before We Cut
Active pipe leaks compound fast — mold growth can begin in 24–48 hours of sustained moisture. Masters Plumbing Service's pipe repair crew is in Comer today, equipped with acoustic and thermal detection tools to find the failure precisely before anything is opened.
